View TSV358IYPT_1329756.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

TSV321-TSV358-TSV324
General purpose input/output rail-to-rail low power operational amplifiers
Features

Pin connections (top view) TSV321RILT (SOT23-5)
Output VDD Non Inverting Input 1 2 3 4 Inverting Input 5 VCC
Operating range VCC = 2.5V to 6V Rail-to-rail input and output Extended Vicm (VDD - 0.2V to VCC + 0.2V) Capable of driving a 32 load resistor High stability: 500pF Available in SOT23-5 micropackage Operating temperature range: -40C, +125C
TSV321ID-TSV321IDT (SO-8)
N.C. Inverting Input Non Inverting Input VDD 1 2 3 4 _ + 8 7 6 5 N.C. VCC Output N.C.
Applications

Battery-powered applications Audio driver (headphone driver) Sensor signal conditioning Laptop/notebook computers
Description
The TSV358 and TSV324 (dual and quad) are low voltage versions of LM358 and LM324 commodity operational amplifiers. TSV321 is the single version. The TSV321/358/324 are able to operate with voltages as low as 2.5V and feature both I/O rail-to-rail. The common mode input voltage extends 200mV at 25C beyond the supply voltages while the output voltage swing is within 100mV of each rail with 600 Ohm load resistor. At VCC = 3V, these devices offer 1.3MHz of gain-bandwidth product and provide high output drive capability typically at 80mA-load. These features make the TSV3xx family ideal for active filters, general purpose low-voltage applications, and general purpose portable devices.
TSV358IST-TSV358ID-TSV358IDT-TSV358IPT (SO-8, miniSO-8, TSSOP8)
Output 1 Inverting Input 1 Non Inverting Input 1 VDD 1 2 3 4 _ + _ + 8 7 6 5 VCC Output 2 Inverting Input 2 Non Inverting Input 2
TSV324ID-TSV324IDT-TSV324IPT (SO-14, TSSOP14)
Output 1 Inverting Input 1 Non Inverting Input 1 VCC Non Inverting Input 2 Inverting Input 2 Output 2
1 2 3 4 5 6 7 + _ + _ _ + _ +
14 Output 4 13 Inverting Input 4 12 Non Inverting Input 4 11 VDD 10 Non Inverting Input 3 9 8 Inverting Input 3 Output 3
June 2007
Rev 4
1/19
www.st.com 19
Contents
TSV321-TSV358-TSV324
Contents
1 2 3 Absolute maximum ratings and operating conditions . . . . . . . . . . . . . 3 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3.1 3.2 3.3 3.4 3.5 3.6 SO-8 package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 TSSOP8 package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 MiniSO-8 package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 SO-14 package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 TSSOP14 package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 SOT23-5 package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
4 5
Ordering information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
2/19
TSV321-TSV358-TSV324
Absolute maximum ratings and operating conditions
1
Absolute maximum ratings and operating conditions
Table 1.
Symbol VCC Vid Vin Tstg Tj Supply voltage (1) Differential input voltage Input voltage Storage temperature Maximum junction temperature Thermal resistance junction to SOT23-5 SO-8 SO-14 TSSOP8 TSSOP14 MiniSO-8 ambient(3) (4) 250 125 103 120 100 190 81 40 31 37 32 39 2 200
(7) (2)
Absolute maximum ratings
Parameter Value 7 1 VDD-0.3 to VCC +0.3 -65 to +150 150 Unit V V V C C C/W
Rthja
Rthjc
Thermal resistance junction to case SOT23-5 SO-8 SO-14 TSSOP8 TSSOP14 MiniSO-8 HBM: human body model(5)
C/W
kV V kV mA C
(8)
ESD
MM: machine model
(6)
CDM: charged device model Latch-up immunity
1.5 200 250 See note
Lead temperature (soldering, 10s) Output short-circuit duration
1. All voltages values, except differential voltage are with respect to network terminal. 2. Differential voltages are the non-inverting input terminal with respect to the inverting input terminal. If Vid > 1V, the maximum input current must not exceed 1mA. When Vid > 1V, an input series resistor must be added to limit input current. 3. Short-circuits can cause excessive heating and destructive dissipation. 4. Rth are typical values. 5. Human body model: 100pF discharged through a 1.5k resistor between two pins of the device, done for all couples of pin combinations with other pins floating. 6. Machine model: a 200pF cap is charged to the specified voltage, then discharged directly between two pins of the device with no external series resistor (internal resistor < 5), done for all couples of pin combinations with other pins floating. 7. Charged device model: all pins plus package are charged together to the specified voltage and then discharged directly to the ground. 8. Short-circuits from the output to VCCcan cause excessive heating. The maximum output current is approximately 80mA, independent of the magnitude of VCC. Destructive dissipation can result from simultaneous short-circuits on all amplifiers.
3/19
Absolute maximum ratings and operating conditions Table 2.
Symbol VCC Vicm Toper Supply voltage Common mode input voltage range Top = 25C, 2.5 VCC 6V Tmin < Top < Tmax, 2.5 VCC 5.5V Operating free air temperature range
TSV321-TSV358-TSV324
Operating conditions
Parameter Value 2.5 to 6 VDD - 0.2 to VCC + 0.2 VDD to VCC -40 to + 125 Unit V V C
4/19
TSV321-TSV358-TSV324
Electrical characteristics
2
Table 3.
Symbol
Electrical characteristics
Electrical characteristics at VCC = +3V, VDD = 0V, RL, CL connected to VCC/2, and Tamb = 25C (unless otherwise specified)
Parameter Test conditions Vicm = Vout = VCC /2 TSV321/358/324 Tmin < Top < Tmax TSV321A/358A/324A Tmin < Top < Tmax Min. Typ. Max. Unit
0.2 0.1 2
Vio
Input offset voltage
3 6 1 3
mV
Vio Iio Iib CMR
Input offset voltage drift Input offset current (1) Input bias current (1) Common mode rejection ratio 20 log (Vic/Vio) Large signal voltage gain Vicm = Vout = VCC /2 Tmin Tamb Tmax Vicm = Vout = VCC /2 Tmin Tamb Tmax 0 Vicm VCC, Vout = VCC /2 Vout = 0.5V to 2.5V RL = 2k RL = 600 Vid = 100mV RL = 2k RL = 600 Tmin Tamb Tmax, RL = 2k Tmin Tamb Tmax, RL = 600 Vid = -100mV RL = 2k RL = 600 Tmin Tamb Tmax, RL = 2k Tmin Tamb Tmax, RL = 600 Vid = 100mV, VO = VDD Vid = -100mV, VO = VCC AVCL = 1, no load Tmin Tamb Tmax RL = 10k CL = 100pF, f = 100kHz , , RL = 10k CL = 100pF CL = 100pF 1 0.42 20 20 60
V/C 30 60 125 150 nA nA dB
3 40
80
Avd
80 74 2.82 2.80 2.82 2.80
92 95 2.95 2.95
dB
VOH
High level output voltage
V
VOL
Low level output voltage
88 115
120 160 120 160
mV
Output source current Io ICC GBP SR m en THD Output sink current Supply current (per amplifier) Gain bandwidth product Slew rate Phase margin Input voltage noise Total harmonic distortion
80 mA 80 420 1.3 0.6 53 27 0.01 650 690 A MHz V/s Degrees nV/ Hz %
1. Maximum values include unavoidable inaccuracies of the industrial tests.
5/19
Electrical characteristics Table 4.
Symbol
TSV321-TSV358-TSV324
Electrical characteristics at VCC = +5V, VDD = 0V, RL, CL connected to VCC/2, and Tamb = 25C (unless otherwise specified)
Parameter Conditions Vicm = Vout = VCC /2 TSV321/358/324 Tmin < Top < Tmax TSV321A/358A/324A Tmin < Top < Tmax Min. Typ. Max. Unit
0.2 0.1 2
Vio
Input offset voltage
3 6 1 3
mV
Vio Iio Iib CMR SVR
Input offset voltage drift Input offset current (1) Input bias current (1) Common mode rejection ratio 20 log (Vic/Vio) Supply voltage rejection ratio 20 log (VCC/Vio) Large signal voltage gain Vicm = Vout = VCC /2 Tmin Tamb Tmax Vicm = Vout = VCC /2 Tmin Tamb Tmax 0 Vicm VCC, Vout = VCC /2 VCC = 2.5 to 5V Vout = 0.5V to 4.5V RL = 2k RL = 600 Vid = 100mV RL = 2k RL = 600 Tmin Tamb Tmax, RL = 2k Tmin Tamb Tmax, RL = 600 Vid = -100mV RL = 2k RL = 600 Tmin Tamb Tmax, RL = 2k Tmin Tamb Tmax, RL = 600 Vid = 100mV, VO = VDD Vid = -100mV, VO = VCC AVCL = 1, no load Tmin Tamb Tmax RL = 10k CL = 100pF, f = 100kHz , , RL = 10k CL = 100pF CL = 100pF 1 0.42 20 20 65 70
V/C 30 60 130 150 nA nA dB dB
3 70
85 90
Avd
83 77 4.80 4.75 4.80 4.75
92 85 4.95 4.90
dB
VOH
High level output voltage
V
VOL
Low level output voltage
88 115
130 188 130 188
mV
Output source current Io ICC GBP SR m en THD Output sink current Supply current (per amplifier) Gain bandwidth product Slew rate Phase margin Input voltage noise Total harmonic distortion
80 mA 80 500 1.4 0.6 55 27 0.01 835 875 A MHz V/s Degrees nV/ Hz %
1. Maximum values include unavoidable inaccuracies of the industrial tests.
6/19
TSV321-TSV358-TSV324
Electrical characteristics
Figure 1.
600 500
Supply current/amplifier vs. supply Figure 2. voltage
550
Supply current/amplifier vs. temperature
Vcc = 5V
Supply Current (A)
500 Supply Current (A) Vcc = 3V 450 400 350 300 250 -40
400 300 200 100 0 0 2 4 Supply Voltage (V) 6 8 Tamb = 25C
-20
0
20
40
60
80
100
120
140
Temperature (C)
Figure 3.
Output power vs. supply voltage
Figure 4.
200
Input offset voltage drift vs. temperature
60 RL = 32 ohms 50 Output Power (mW) 1% distortion 40 30 0.1% distortion 20 10 10% distortion
Input Voltage Drift (V)
150 100 50 0 -50 -100 Vcc = 5V Vcc = 3V
0 1 2 3 4 5 6 Supply Voltage (V)
-150 -40
-20
0
20
40
60
80
100
120
140
Temperature (C)
Figure 5.
10.0
Input bias current vs. temperature
Figure 6.
110
Open loop gain vs. temperature at VCC= 5V
Vcc = 5V Vicm = 2.5V RL = 2 kOhms
Vcc = 3V Vicm = 1.5V Input bias current (nA) 0.0
-10.0
Open Loop Gain (dB)
100
90
RL = 600 ohms
-20.0
80
-30.0
-40.0 -40 -20
0
20
40 60 80 100 Temperature (C)
120 140
70 -40
-20
0
20
40
60
80
100
120
140
Temperature (C)
7/19
Electrical characteristics
TSV321-TSV358-TSV324
Figure 7.
110
Open loop gain vs. temperature at VCC= 3V
Vcc = 3V Vicm = 1.5V
Figure 8.
110 Voltage Referenced to VCC (mV)
High level output voltage vs. temperature
RL = 600 ohms
RL = 2 kOhms
100 90 80 70 60 50 40 -40
Vcc = 5V
Open Loop Gain (dB)
100
Vcc = 3V
90
RL = 600 Ohms
80
70 -40
-20
0
20
40
60
80
100
120
140
-20
0
20
40
60
80
100
120
140
Temperature (C)
Temperature (C)
Figure 9.
110 Voltage Referenced to Gnd (mV)
Low level output voltage vs. temperature
RL = 600 ohms
Figure 10. Output current vs. temperature at VCC= 5V
100
100 90 80 Vcc = 3V 70 60 50 40 -40
-100
Isink
Vcc = 5V
Output Current (mA)
50 Vcc = 5V Vid = 1V 0
-50
Isource
-20
0
20
40
60
80
100
120
140
-40
-20
0
20
40
60
80
100
120
140
Temperature (C)
Temperature (C)
Figure 11. Output current vs. temperature at VCC= 3V
100 Isink
Figure 12. Output current vs. output voltage at VCC= 5V
100 T = -40 C sink T = 125 C Vcc = 5V Vid = 0.1V Vicm = 2.5V T = 125 C -50 T = 25 C T = -40 C source 2.0 3.0 Output Voltage (V) 4.0 5.0 T = 25 C
Vcc = 3V Vid = 1V 0 Isource -50
Output Current (mA)
60 80 100 120 140
Output Current (mA)
50
50
0
-100 -40 -20 0 20 40 Temperature (C)
-100 0.0 1.0
8/19
TSV321-TSV358-TSV324
Electrical characteristics
Figure 13. Output current vs. output voltage at Figure 14. Gain and phase vs. frequency at VCC= 3V VCC= 5V
100 T = -40 C T = 25 C Output Current (mA) 50 sink T = 125 C
70 60 50 Gain (dB) RL = 10K CL = 100 pF Vcc = 5V
180 160 140 Phase () 120 gain phase 100 80 60 40 1E+4 1E+5 1E+6 Frequency (Hz)
0 T = 125 C -50 T = 25 C T = -40 C -100 0.0 0.5 1.0
Vcc = 3V Vid = 0.1V Vicm = 1.5V
40 30 20 10
source 1.5 2.0 2.5 3.0 3.5
0 1E+3
Output Voltage (V)
v
Figure 15. Gain and phase vs. frequency at VCC= 3V
70 60 50 Gain (dB) 40 gain 30 20 10 0 1E+3 phase 100 80 60 40 1E+4 1E+5 Frequency (Hz) 1E+6 RL = 10K CL = 100 pF Vcc = 3V 180 160 140 Phase () Phase () 120
Figure 16. Slew rate vs. temperature at VCC= 5V
0.75 0.70 Slew Rate (V/s) 0.65 0.60 0.55 0.50 0.45 0.40 0.35 -40 Vcc = 5V gain = +1 Vin = 2 to 3V RL = 10kohms CL = 100 pF positive Slew Rate
negative Slew Rate
-20
0
20
40
60
80
100
120
140
Temperature (C)
Figure 17. Slew rate vs. temperature at VCC= 3V
0.70 0.65 Slew Rate (V/s) 0.60 0.55 0.50 0.45 0.40 0.35 -40 Vcc = 3V gain = +1 Vin = 1 to 2V RL = 10kohm CL = 100 pF positive Slew Rate
Figure 18. Distortion vs. frequency
0.150 0.125 0.100 0.075 0.050 0.025 0.000 1E+1 Vcc = 3V Vout = 1Vpp RL = 32 ohms gain = -1
negative Slew Rate
-20
0
20
40
60
80
100
120
140
Distortion (%)
1E+2
1E+3 Frequency (Hz)
1E+4
1E+5
Temperature (C)
9/19
Package information
TSV321-TSV358-TSV324
3
Package information
In order to meet environmental requirements, STMicroelectronics offers these devices in ECOPACK(R) packages. These packages have a lead-free second level interconnect. The category of second level interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. ECOPACK is an STMicroelectronics trademark. ECOPACK specifications are available at: www.st.com.
10/19
TSV321-TSV358-TSV324
Package information
3.1
SO-8 package mechanical data
Dimensions Ref. Min. A A1 A2 b c D H E1 e h L k ccc 0.25 0.40 1 0.10 1.25 0.28 0.17 4.80 5.80 3.80 4.90 6.00 3.90 1.27 0.50 1.27 8 0.10 0.010 0.016 1 0.48 0.23 5.00 6.20 4.00 Millimeters Typ. Max. 1.75 0.25 0.004 0.049 0.011 0.007 0.189 0.228 0.150 0.193 0.236 0.154 0.050 0.020 0.050 8 0.004 0.019 0.010 0.197 0.244 0.157 Min. Inches Typ. Max. 0.069 0.010
11/19
Package information
TSV321-TSV358-TSV324
3.2
TSSOP8 package mechanical data
)
Dimensions Ref. Min. A A1 A2 b c D E E1 e k L L1 aaa 0 0.45 0.60 1 0.1 0.05 0.80 0.19 0.09 2.90 6.20 4.30 3.00 6.40 4.40 0.65 8 0.75 0 0.018 0.024 0.039 0.004 1.00 Millimeters Typ. Max. 1.2 0.15 1.05 0.30 0.20 3.10 6.60 4.50 0.002 0.031 0.007 0.004 0.114 0.244 0.169 0.118 0.252 0.173 0.0256 8 0.030 0.039 Min. Inches Typ. Max. 0.047 0.006 0.041 0.012 0.008 0.122 0.260 0.177
12/19
TSV321-TSV358-TSV324
Package information
3.3
MiniSO-8 package mechanical data
Dimensions Ref. Min. A A1 A2 b c D E E1 e K L L1 0 0.40 0.55 0.05 0.78 0.25 0.13 2.90 4.75 2.90 0.10 0.86 0.33 0.18 3.00 4.90 3.00 0.65 6 0.70 0.10 0 0.016 0.022 Millimeters Typ. Max. 1.1 0.15 0.94 0.40 0.23 3.10 5.05 3.10 0.002 0.031 0.010 0.005 0.114 0.187 0.114 0.004 0.034 0.013 0.007 0.118 0.193 0.118 0.026 6 0.028 0.004 Min. Inches Typ. Max. 0.043 0.006 0.037 0.016 0.009 0.122 0.199 0.122
13/19
Package information
TSV321-TSV358-TSV324
3.4
SO-14 package mechanical data
Dimensions Ref. Min. A a1 a2 b b1 C c1 D E e e3 F G L M S 3.8 4.6 0.5 8.55 5.8 1.27 7.62 4.0 5.3 1.27 0.68 8 (max.) 0.149 0.181 0.019 8.75 6.2 0.35 0.19 0.5 45 (typ.) 0.336 0.228 0.050 0.300 0.157 0.208 0.050 0.026 0.344 0.244 0.1 Millimeters Typ. Max. 1.75 0.2 1.65 0.46 0.25 0.013 0.007 0.019 0.003 Min. Inches Typ. Max. 0.068 0.007 0.064 0.018 0.010
14/19
TSV321-TSV358-TSV324
Package information
3.5
TSSOP14 package mechanical data
Dimensions Ref. Min. A A1 A2 b c D E E1 e K L 0 0.45 0.60 0.05 0.8 0.19 0.09 4.9 6.2 4.3 5 6.4 4.4 0.65 BSC 8 0.75 0 0.018 0.024 1 Millimeters Typ. Max. 1.2 0.15 1.05 0.30 0.20 5.1 6.6 4.48 0.002 0.031 0.007 0.004 0.193 0.244 0.169 0.197 0.252 0.173 0.0256 BSC 8 0.030 0.004 0.039 Min. Inches Typ. Max. 0.047 0.006 0.041 0.012 0.0089 0.201 0.260 0.176
A
A2 A1 b e K c L E
D
E1
PIN 1 IDENTIFICATION
1
15/19
Package information
TSV321-TSV358-TSV324
3.6
SOT23-5 package mechanical data
Dimensions Ref. Min. A A1 A2 b C D E E1 e e1 L 0.35 0.90 0.00 0.90 0.35 0.09 2.80 2.60 1.50 0.95 1.9 0.55 13.7 Millimeters Typ. Max. 1.45 0.15 1.30 0.50 0.20 3.00 3.00 1.75 Min. 35.4 0.00 35.4 13.7 3.5 110.2 102.3 59.0 37.4 74.8 21.6 Mils Typ. Max. 57.1 5.9 51.2 19.7 7.8 118.1 118.1 68.8
16/19
TSV321-TSV358-TSV324
Ordering information
4
Table 5.
Ordering information
Order codes
Temperature range Package Packaging Marking K174 SOT23-5 Tape & reel K178 SOT23-5 (Automotive grade level) SO-8 SO-8 (Automotive grade level) SO-8 K179 Tape & reel K187 Tube or tape & reel Tube or tape & reel Tube or tape & reel Tube or tape & reel Tube or tape & reel Tape & reel V358A V358Y Tape & reel V58AY K175 MiniSO-8 Tape & reel K184 SO-14 Tube or tape & reel Tube or tape & reel V324AY TSSOP14 (Thin shrink outline package) TSSOP14 (Automotive grade level) V324IP Tape & reel V324A V324AY Tape & reel V324Y V324ID V324AI V324YD SO-14 (Automotive grade level) V321ID V321Y V321AI V358ID V358AID V358YD V358AY V358I
Part number TSV321RILT TSV321RAILT TSV321RIYLT
(1)
TSV321RAIYLT(1) TSV321ID/IDT TSV321IYD/IYDT(1) TSV321AID/IDT TSV358ID/IDT
SO-8 TSV358AID/IDT TSV358IYD/IYDT
(1) (1)
TSV358AIYD/AIYDT TSV358IPT TSV358AIPT TSV358IYPT
(1)
SO-8 (Automotive grade level) -40C to +125C TSSOP8 (Thin shrink outline package) TSSOP8 (Automotive grade level)
TSV358AIYPT(1) TSV358IST TSV358AIST TSV324ID/IDT TSV324AID/AIDT TSV324IYD/IYDT(1) TSV324AIYD/AIYDT(1) TSV324IPT TSV324AIPT TSV324AIYPT(1) TSV324IYPT
(1)
1. Qualified and characterized according to AEC Q100 and Q003 or equivalent, advanced screening according to AEC Q001 & Q 002 or equivalent.
17/19
Revision history
TSV321-TSV358-TSV324
5
Revision history
Date 2-Aug-2005 20-Sep-2005 Revision 1 2 Changes First release - Products in full production. Addition of TS321A/TS324A/TS358A data in tables in Section 2: Electrical characteristics on page 5. Minor formatting and grammatical changes. Missing PPAP references inserted see Section 4: Ordering information on page 17. Correction made on output drive capability, 80mA in description on cover page. SVR measurement conditions inserted in electrical characteristics tables. Offset voltage limit in temperature added in Section 2: Electrical characteristics on page 5. Correction made on Input Bias Current typical value in Section 2: Electrical characteristics on page 5. Captions of electrical characteristics figures updated. Automotive grade order codes added to Section 4: Ordering information on page 17.
7-Dec-2005
3
28-Jun-2007
4
18/19
TSV321-TSV358-TSV324
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries ("ST") reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST's terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST'S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER'S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
(c) 2007 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com
19/19

▲Up To Search▲

Price & Availability of TSV358IYPT

	To Download TSV358IYPT Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .